Harvard scientist develops process to convert CO2 into industrial fuels

Nov 19 2018


A fellow at the Rowland Institute at Harvard, Wang and colleagues have developed an improved system to use renewable electricity to reduce carbon dioxide into carbon monoxide (CO) — a key commodity used in a number of industrial processes.

The system is described in a Nov. 8 paper published in Joule, a newly launched sister journal of Cell Press.

“The most promising idea may be to connect these devices with coal-fired power plants or other industry that produces a lot of CO2,” Wang said. “About 20 percent of those gases are CO2, so if you can pump them into this cell … and combine it with clean electricity, then we can potentially produce useful chemicals out of these wastes in a sustainable way, and even close part of that CO2 cycle.”

The new system, Wang said, represents a dramatic step forward from the one he and colleagues first described in a 2017 paper in Chem.

The old system was barely the size of a cellphone and relied on two electrolyte-filled chambers, each of which held an electrode. The new system is cheaper and relies on high concentrations of CO2 gas and water vapor to operate more efficiently. Just one 10-by-10-centimeter cell can produce as much as four liters of CO per hour, said Wang.

The new system addresses the two main challenges — cost and scalability — that were seen as limiting the initial approach, he said.

“In that earlier work, we had discovered the single nickel atom catalysts which are very selective for reducing CO2 to CO … but one of the challenges we faced was that the materials were expensive to synthesize,” Wang said. “The support we were using to anchor single nickel atoms was based on graphene, which made it very difficult to scale up if you wanted to produce it at gram or even kilogram scale for practical use in the future.”

To address that problem, he said, his team turned to a commercial product that’s thousands of times cheaper than graphene as an alternative support — carbon black.

Using a process similar to electrostatic attraction, Wang and colleagues are able to absorb single nickel atoms (positively charged) into defects (negatively charged) in carbon black nanoparticles, with the resulting material being both low-cost and highly selective for CO2 reduction.

“Right now, the best we can produce is grams, but previously we could only produce milligrams per batch,” Wang said. “But this is only limited by the synthesis equipment we have; if you had a larger tank, you could make kilograms or even tons of this catalyst.”

The other challenge Wang and colleagues had to overcome was tied to the fact that the original system only worked in a liquid solution.

“The problem was that the CO2 we can reduce in that system are only those dissolved in water; most of the molecules surrounding the catalyst were water,” he said. “There was only a trace amount of CO2, so it was pretty inefficient.”

While it may be tempting to simply increase the voltage applied on the catalyst to increase the reaction rate, that can have the unintended consequence of splitting water, not reducing CO2, Wang said.

“If you deplete the CO2 that’s close to the electrode, other molecules have to diffuse to the electrode, and that takes time,” Wang said. “But if you’re increasing the voltage, it’s more likely that the surrounding water will take that opportunity to react and split into hydrogen and oxygen.”

The solution proved to be relatively simple — to avoid splitting water, the team took the catalyst out of solution.

“We replace that liquid water with water vapor, and feed in high-concentration CO2 gas,” he said. “So if the old system was more than 99 percent water and less than 1 percent CO2, now we can completely reverse that, and pump 97 percent CO2 gas and only 3 percent water vapor into this system. Before those, liquid water also functioned as ion conductors in the system, and now we use ion exchange membranes instead to help ions move around without liquid water.

“The impact is that we can deliver an order of magnitude higher current density,” he continued. “Previously, we were operating at about 10 milliamps-per-centimeter squared, but today we can easily ramp up to 100 milliamps.”

Going forward, Wang said, the system still has challenges to overcome — particularly related to stability.

“If you want to use this to make an economic or environmental impact, it needs to have a continuous operation of thousands of hours,” he said. “Right now, we can do this for tens of hours, so there’s still a big gap, but I believe those problems can be addressed with more detailed analysis of both the CO2reduction catalyst and the water oxidation catalyst.”

Ultimately, Wang said, the day may come when industry will be able to capture the CO2 that is now released into the atmosphere and transform it into useful products.

“Carbon monoxide is not a particularly high-value chemical product,” Wang said. “To explore more possibilities, my group has also developed several copper-based catalysts that can further reduce CO2 into products that are much more valuable.”

Wang credited the freedom he enjoyed at the Rowland Institute with helping lead to breakthroughs like the new system.

“Rowland has provided me, as an early career researcher, a great platform for independent research, which initiates a large portion of the research directions my group will continue to push forward,” said Wang, who recently accepted a position at Rice University. “I will definitely miss my days here.”

 

Rowland Institute


Previous: Carbon fibers from greenhouse gas

Next: ETI report on brine production and its Impact on UK CO2 storage

Issue 65 - Sept - Oct 2018

CCS in Canada - CCS Knowledge Centre: large scale CCS ready for 2nd generation .. New heat integration strategy to improve efficiency of a CCS facility .. University of Calgary field research station tests nanoparticles to better monitor subsurface C.....


Subscribers can access the latest issue here